Track-Bed^™

Track-Bed is made of a sound-deadening material that cushions vibrations for smoother operation. It is a high quality and low-cost alternative to other rail beds. Track-Bed is compatible with cork, remains flexible, requires no pre-soaking, and will not crumble.

N Scale

Track-Bed is a high quality, economic alternative to other rail beds and aligns well with cork. It absorbs irregularities on your layout while also providing a quiet and smooth train operation. Track-Bed requires no pre-soaking, remains flexible, and will not crumble.
Frequently Asked Questions
- I am interested in your Track-Bed. Is it black, dark gray or light gray?
  
  The Track-Bed is a dark gray.
- What is the best way to attach Track-Bed?
  
  For a strong bond, rough-up the bottom of Track-Bed™ with 80-grit sandpaper and attach using the contact method, working in small, manageable sections.
  
  Contact Method - Apply Foam Tack Glue™ to both surfaces, allow to set for approximately 20 minutes, but no longer than 1 hour, until tacky, then apply.
  
  Click here to view a video on installing Track-Bed.
- How are turnout switches attached to Risers under Track-Bed?
  
  Cut out a section of Riser where the under table switches will be located. Use 1/4" piece of Foam Sheet, Masonite or plywood to bridge the gap. Notch each end of the Riser to accomodate thickness of material. Material should be level with Riser. Glue into place and mount the switch.
- What is the best method for laying out Track-Bed for placement on my layout?
  
  Lay out Track-Bed™ in one piece. Accommodate tight curves by separating the Track-Bed into two narrow strips along the slit that runs lengthwise. Lay the two pieces seperately, butting them snuggly in the middle. Do this by first drawing a center line for your track. Lay each half strip of Track-Bed on either side along this center line.
  
  Click here to view a video on installing Track-Bed.
- Is the Track-Bed solvent resistant?
  
  Yes, Track-Bed is solvent resistant.
- Why is Track-Bed better than cork?
  
  Track-Bed® absorbs the noise and vibration of train operations, so you can enjoy the true "clickety-clack" sound. Track-Bed costs less, does not require pre-soaking, and is easy to apply. It will not dry out, crack and crumble like cork. Since Track-Bed is compatible and aligns easily with cork, you can update your cork bed at any time.
- Can your Track-Bed be used with any brand of track and on any layout?
  
  Yes, our Track-Bed™ works great on any type layout with any kind of track of a standard width. For larger scales, consider using Track-Bed Sheets.
- Is it easier to use the rolls of Track-Bed or the strips?
  
  It really is the users preference, both are easy to use. Generally speaking, Track-Bed Rolls are easier to use when modeling a larger layout with a lot of straightaways and standard curves. Track-Bed Strips are easier to use when modeling a smaller layout with a lot of sharp curves and turnouts.
- After I have glued the Track-Bed to my table top and it dries, can I use plastic screws to further secure my track to the Track-Bed?
  
  We do not manufacture plastic screws and have never tested their usage. This is how we recommend you attach track to your Track-Bed.
  
  We recommend using Foam Tack Glue. Sand surface of Track-Bed with 120-grit sandpaper, then spread a thin layer of glue over the Track-Bed surface and install track. Pin in place with Foam Nails while drying.
- How do I attach Track and Track-Bed to my layout?
  
  We recommend using Foam Tack Glue to attach Track-Bed and Track to a layout.
  
  There are different application methods for attaching Track-Bed to your layout depending on the base material.
  
  Plaster surfaces: Spread a thin, even layer of Foam Tack Glue where Track-Bed will be installed. Lay Track-Bed and pin in place with Foam Nails to secure while drying. Work in two to three-foot sections. This application method also allows the modeler to make adjustments while installing Track-Bed.
  
  A permanent application method for plaster and other surfaces: Use the Contact Gluing Method. Apply Foam Tack Glue to both contact surfaces. Let dry until clear and tacky (maximum working time is 1 hour), and then press Track-Bed in place. Installation of Track-Bed has to be precise, because glue will bond instantly. Place Track-Bed in manageable sections.
  
  For both application methods, we recommend sanding the top and bottom surface of Track-Bed with 120-grit sandpaper before installation.
  
  To attach your track to the Track-Bed, spread a thin, even layer of Foam Tack Glue on top of the Track-Bed. Place pieces of track on glue and pin in place with Foam Nails to secure while drying.
  
  Click here to view a video on installing Track-Bed.
- What adhesive is the most suitable for securing Woodland Scenics trackbed to a painted or unpainted plywood surface?
  
  We recommend using Foam Tack Glue to adhere Track-Bed to a plywood base.
  
  If the plywood is painted, we suggest that you use 80 or 100 grit sandpaper to rough up the surface. This will give a tooth for the adhesive to hold on to. If the plywood isn't painted, you do not have to do this. To attach Track-Bed to a plywood base, use the contact gluing method. Apply adhesive to both contact surfaces and let dry until clear and tacky (maximum working time is one hour). When installing Track-Bed, the glue will bond instantly.
- What is the minimum radius for N, HO and O scale Track-Bed?
  
  The minimum turn radius for:
  
  N scale 9 1/2" - 9 3/4"
  
  HO scale 15"
  
  O scale 27"
- How do I apply track-bed along curves?
  
  Separate Track-Bed into two sections along the score line. Draw a centerline along the curve. Using the centerline as a guide, press Track-Bed sections in place separately, butting them snugly side-by-side.
  
  We recommend attaching Track-Bed with Foam Tack Glue.
  
  Click here to view a portion of a video demonstrating how to install Track-Bed along a curve.
- What are the ratios of the different scales?
  
  Model Scales
  
  G = 1:24
  
  O = 1:48
  
  S = 1:64
  
  OO = 1:76.2
  
  HO = 1:87
  
  N = 1:160
  
  Z = 1:220
- When using the Foam Tack Glue on Track-Bed material, can it be removed safely in the future?
  
  Yes. Soften Foam Tack Glue with warm, soapy water. If the glue is difficult to remove, use denatured alcohol.
- I am using Track-Bed, and securing the track with Foam Tack Glue. Now, I need to move one of the tracks. How can I get the Foam Tack Glue to release?
  
  To remove Track-Bed™, soften the Foam Tack Glue™ with warm, soapy water. If the glue is hard to remove, use denature alcohol.
- How much Foam Tack Glue will I need when I lay my Track-Bed?
  
  N scale Track-Bed - 1/3 oz of Foam Tack Glue covers approximately 4 feet of N scale Track-Bed
  
  HO scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 2 feet of HO scale Track-Bed
  
  O scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 1 foot of O scale Track-Bed
  
  Super Sheets - 1 oz per Super Sheet. 1 bottle (12 fl oz) will do 12 Super Sheets.
  
  NOTE: Coverage is approximate. Exact coverage depends on thickness of application.
HO Scale

Track-Bed is a high quality, economic alternative to other rail beds and aligns well with cork. It absorbs irregularities on your layout while also providing a quiet and smooth train operation. Track-Bed requires no pre-soaking, remains flexible, and will not crumble.
Frequently Asked Questions
- I am interested in your Track-Bed. Is it black, dark gray or light gray?
  
  The Track-Bed is a dark gray.
- What is the best way to attach Track-Bed?
  
  For a strong bond, rough-up the bottom of Track-Bed™ with 80-grit sandpaper and attach using the contact method, working in small, manageable sections.
  
  Contact Method - Apply Foam Tack Glue™ to both surfaces, allow to set for approximately 20 minutes, but no longer than 1 hour, until tacky, then apply.
  
  Click here to view a video on installing Track-Bed.
- How are turnout switches attached to Risers under Track-Bed?
  
  Cut out a section of Riser where the under table switches will be located. Use 1/4" piece of Foam Sheet, Masonite or plywood to bridge the gap. Notch each end of the Riser to accomodate thickness of material. Material should be level with Riser. Glue into place and mount the switch.
- What is the best method for laying out Track-Bed for placement on my layout?
  
  Lay out Track-Bed™ in one piece. Accommodate tight curves by separating the Track-Bed into two narrow strips along the slit that runs lengthwise. Lay the two pieces seperately, butting them snuggly in the middle. Do this by first drawing a center line for your track. Lay each half strip of Track-Bed on either side along this center line.
  
  Click here to view a video on installing Track-Bed.
- Is the Track-Bed solvent resistant?
  
  Yes, Track-Bed is solvent resistant.
- Why is Track-Bed better than cork?
  
  Track-Bed® absorbs the noise and vibration of train operations, so you can enjoy the true "clickety-clack" sound. Track-Bed costs less, does not require pre-soaking, and is easy to apply. It will not dry out, crack and crumble like cork. Since Track-Bed is compatible and aligns easily with cork, you can update your cork bed at any time.
- Can your Track-Bed be used with any brand of track and on any layout?
  
  Yes, our Track-Bed™ works great on any type layout with any kind of track of a standard width. For larger scales, consider using Track-Bed Sheets.
- What are the HO scale track measurements from rail to rail, and also tie to tie.
  
  NMRA standards note minimum and maximum values, instead of limits, for Prototype HO (1:87) track.
  
  Measurements (inside rail to inside rail)
  
  Minimum 16.48 mm
  
  Maximum 16.84 mm
  
  There are no NMRA standards for ties.
  
  If you are not concerned about NMRA standards, below are general measurements.
  
  HO Track
  
  Approximately 16.5 mm from inside rail to inside rail.
  
  Ties
  
  Real World (HO scale)
  
  Length: 102" (1.17" / 29.6 mm)
  
  Width: 9" (0.103" / 2.6 mm)
  
  Height: 7" (0.08" / 2 mm)
  
  Center-to-Center Spacing: 19.5"-21" (0.22"-0.24" / 5.6 mm-6.1) mm
- Is it easier to use the rolls of Track-Bed or the strips?
  
  It really is the users preference, both are easy to use. Generally speaking, Track-Bed Rolls are easier to use when modeling a larger layout with a lot of straightaways and standard curves. Track-Bed Strips are easier to use when modeling a smaller layout with a lot of sharp curves and turnouts.
- After I have glued the Track-Bed to my table top and it dries, can I use plastic screws to further secure my track to the Track-Bed?
  
  We do not manufacture plastic screws and have never tested their usage. This is how we recommend you attach track to your Track-Bed.
  
  We recommend using Foam Tack Glue. Sand surface of Track-Bed with 120-grit sandpaper, then spread a thin layer of glue over the Track-Bed surface and install track. Pin in place with Foam Nails while drying.
- How do I attach Track and Track-Bed to my layout?
  
  We recommend using Foam Tack Glue to attach Track-Bed and Track to a layout.
  
  There are different application methods for attaching Track-Bed to your layout depending on the base material.
  
  Plaster surfaces: Spread a thin, even layer of Foam Tack Glue where Track-Bed will be installed. Lay Track-Bed and pin in place with Foam Nails to secure while drying. Work in two to three-foot sections. This application method also allows the modeler to make adjustments while installing Track-Bed.
  
  A permanent application method for plaster and other surfaces: Use the Contact Gluing Method. Apply Foam Tack Glue to both contact surfaces. Let dry until clear and tacky (maximum working time is 1 hour), and then press Track-Bed in place. Installation of Track-Bed has to be precise, because glue will bond instantly. Place Track-Bed in manageable sections.
  
  For both application methods, we recommend sanding the top and bottom surface of Track-Bed with 120-grit sandpaper before installation.
  
  To attach your track to the Track-Bed, spread a thin, even layer of Foam Tack Glue on top of the Track-Bed. Place pieces of track on glue and pin in place with Foam Nails to secure while drying.
  
  Click here to view a video on installing Track-Bed.
- What adhesive is the most suitable for securing Woodland Scenics trackbed to a painted or unpainted plywood surface?
  
  We recommend using Foam Tack Glue to adhere Track-Bed to a plywood base.
  
  If the plywood is painted, we suggest that you use 80 or 100 grit sandpaper to rough up the surface. This will give a tooth for the adhesive to hold on to. If the plywood isn't painted, you do not have to do this. To attach Track-Bed to a plywood base, use the contact gluing method. Apply adhesive to both contact surfaces and let dry until clear and tacky (maximum working time is one hour). When installing Track-Bed, the glue will bond instantly.
- What is the minimum radius for N, HO and O scale Track-Bed?
  
  The minimum turn radius for:
  
  N scale 9 1/2" - 9 3/4"
  
  HO scale 15"
  
  O scale 27"
- How do I apply track-bed along curves?
  
  Separate Track-Bed into two sections along the score line. Draw a centerline along the curve. Using the centerline as a guide, press Track-Bed sections in place separately, butting them snugly side-by-side.
  
  We recommend attaching Track-Bed with Foam Tack Glue.
  
  Click here to view a portion of a video demonstrating how to install Track-Bed along a curve.
- Is the HO Track-Bed (roadbed) compatible with OO track?
  
  HO Scale Track Bed (roadbed) is compatible with OO Gauge track.
- What are the ratios of the different scales?
  
  Model Scales
  
  G = 1:24
  
  O = 1:48
  
  S = 1:64
  
  OO = 1:76.2
  
  HO = 1:87
  
  N = 1:160
  
  Z = 1:220
- When using the Foam Tack Glue on Track-Bed material, can it be removed safely in the future?
  
  Yes. Soften Foam Tack Glue with warm, soapy water. If the glue is difficult to remove, use denatured alcohol.
- I am using Track-Bed, and securing the track with Foam Tack Glue. Now, I need to move one of the tracks. How can I get the Foam Tack Glue to release?
  
  To remove Track-Bed™, soften the Foam Tack Glue™ with warm, soapy water. If the glue is hard to remove, use denature alcohol.
- How much Foam Tack Glue will I need when I lay my Track-Bed?
  
  N scale Track-Bed - 1/3 oz of Foam Tack Glue covers approximately 4 feet of N scale Track-Bed
  
  HO scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 2 feet of HO scale Track-Bed
  
  O scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 1 foot of O scale Track-Bed
  
  Super Sheets - 1 oz per Super Sheet. 1 bottle (12 fl oz) will do 12 Super Sheets.
  
  NOTE: Coverage is approximate. Exact coverage depends on thickness of application.
O Scale

Track-Bed is a high quality, economic alternative to other rail beds and aligns well with cork. It absorbs irregularities on your layout while also providing a quiet and smooth train operation. Track-Bed requires no pre-soaking, remains flexible, and will not crumble.
Frequently Asked Questions
- I am wondering why the O scale Track-Bed is wider than the foam inclines and risers. Am I missing something?
  
  When modeling in O scale, Inclines and Risers need to be placed side-by-side to double their width.
- I am interested in your Track-Bed. Is it black, dark gray or light gray?
  
  The Track-Bed is a dark gray.
- What is the best way to attach Track-Bed?
  
  For a strong bond, rough-up the bottom of Track-Bed™ with 80-grit sandpaper and attach using the contact method, working in small, manageable sections.
  
  Contact Method - Apply Foam Tack Glue™ to both surfaces, allow to set for approximately 20 minutes, but no longer than 1 hour, until tacky, then apply.
  
  Click here to view a video on installing Track-Bed.
- How are turnout switches attached to Risers under Track-Bed?
  
  Cut out a section of Riser where the under table switches will be located. Use 1/4" piece of Foam Sheet, Masonite or plywood to bridge the gap. Notch each end of the Riser to accomodate thickness of material. Material should be level with Riser. Glue into place and mount the switch.
- What is the best method for laying out Track-Bed for placement on my layout?
  
  Lay out Track-Bed™ in one piece. Accommodate tight curves by separating the Track-Bed into two narrow strips along the slit that runs lengthwise. Lay the two pieces seperately, butting them snuggly in the middle. Do this by first drawing a center line for your track. Lay each half strip of Track-Bed on either side along this center line.
  
  Click here to view a video on installing Track-Bed.
- Is the Track-Bed solvent resistant?
  
  Yes, Track-Bed is solvent resistant.
- Why is Track-Bed better than cork?
  
  Track-Bed® absorbs the noise and vibration of train operations, so you can enjoy the true "clickety-clack" sound. Track-Bed costs less, does not require pre-soaking, and is easy to apply. It will not dry out, crack and crumble like cork. Since Track-Bed is compatible and aligns easily with cork, you can update your cork bed at any time.
- Can your Track-Bed be used with any brand of track and on any layout?
  
  Yes, our Track-Bed™ works great on any type layout with any kind of track of a standard width. For larger scales, consider using Track-Bed Sheets.
- What is the difference between O and On30 scale? What scale track, risers and TrackBed are compatible?
  
  The "n" stands for narrow. On30 describes the modeling of narrow gauge railways, using O scale trains with narrow tracks that run on HO gauge track. For your On30, you can use SubTerrain Risers and Track-Bed.
- Is it easier to use the rolls of Track-Bed or the strips?
  
  It really is the users preference, both are easy to use. Generally speaking, Track-Bed Rolls are easier to use when modeling a larger layout with a lot of straightaways and standard curves. Track-Bed Strips are easier to use when modeling a smaller layout with a lot of sharp curves and turnouts.
- After I have glued the Track-Bed to my table top and it dries, can I use plastic screws to further secure my track to the Track-Bed?
  
  We do not manufacture plastic screws and have never tested their usage. This is how we recommend you attach track to your Track-Bed.
  
  We recommend using Foam Tack Glue. Sand surface of Track-Bed with 120-grit sandpaper, then spread a thin layer of glue over the Track-Bed surface and install track. Pin in place with Foam Nails while drying.
- How do I attach Track and Track-Bed to my layout?
  
  We recommend using Foam Tack Glue to attach Track-Bed and Track to a layout.
  
  There are different application methods for attaching Track-Bed to your layout depending on the base material.
  
  Plaster surfaces: Spread a thin, even layer of Foam Tack Glue where Track-Bed will be installed. Lay Track-Bed and pin in place with Foam Nails to secure while drying. Work in two to three-foot sections. This application method also allows the modeler to make adjustments while installing Track-Bed.
  
  A permanent application method for plaster and other surfaces: Use the Contact Gluing Method. Apply Foam Tack Glue to both contact surfaces. Let dry until clear and tacky (maximum working time is 1 hour), and then press Track-Bed in place. Installation of Track-Bed has to be precise, because glue will bond instantly. Place Track-Bed in manageable sections.
  
  For both application methods, we recommend sanding the top and bottom surface of Track-Bed with 120-grit sandpaper before installation.
  
  To attach your track to the Track-Bed, spread a thin, even layer of Foam Tack Glue on top of the Track-Bed. Place pieces of track on glue and pin in place with Foam Nails to secure while drying.
  
  Click here to view a video on installing Track-Bed.
- What adhesive is the most suitable for securing Woodland Scenics trackbed to a painted or unpainted plywood surface?
  
  We recommend using Foam Tack Glue to adhere Track-Bed to a plywood base.
  
  If the plywood is painted, we suggest that you use 80 or 100 grit sandpaper to rough up the surface. This will give a tooth for the adhesive to hold on to. If the plywood isn't painted, you do not have to do this. To attach Track-Bed to a plywood base, use the contact gluing method. Apply adhesive to both contact surfaces and let dry until clear and tacky (maximum working time is one hour). When installing Track-Bed, the glue will bond instantly.
- What is the minimum radius for N, HO and O scale Track-Bed?
  
  The minimum turn radius for:
  
  N scale 9 1/2" - 9 3/4"
  
  HO scale 15"
  
  O scale 27"
- How do I apply track-bed along curves?
  
  Separate Track-Bed into two sections along the score line. Draw a centerline along the curve. Using the centerline as a guide, press Track-Bed sections in place separately, butting them snugly side-by-side.
  
  We recommend attaching Track-Bed with Foam Tack Glue.
  
  Click here to view a portion of a video demonstrating how to install Track-Bed along a curve.
- What are the ratios of the different scales?
  
  Model Scales
  
  G = 1:24
  
  O = 1:48
  
  S = 1:64
  
  OO = 1:76.2
  
  HO = 1:87
  
  N = 1:160
  
  Z = 1:220
- When using the Foam Tack Glue on Track-Bed material, can it be removed safely in the future?
  
  Yes. Soften Foam Tack Glue with warm, soapy water. If the glue is difficult to remove, use denatured alcohol.
- I am using Track-Bed, and securing the track with Foam Tack Glue. Now, I need to move one of the tracks. How can I get the Foam Tack Glue to release?
  
  To remove Track-Bed™, soften the Foam Tack Glue™ with warm, soapy water. If the glue is hard to remove, use denature alcohol.
- How much Foam Tack Glue will I need when I lay my Track-Bed?
  
  N scale Track-Bed - 1/3 oz of Foam Tack Glue covers approximately 4 feet of N scale Track-Bed
  
  HO scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 2 feet of HO scale Track-Bed
  
  O scale Track Bed - 1/3 oz of Foam Tack Glue covers approximately 1 foot of O scale Track-Bed
  
  Super Sheets - 1 oz per Super Sheet. 1 bottle (12 fl oz) will do 12 Super Sheets.
  
  NOTE: Coverage is approximate. Exact coverage depends on thickness of application.

Login

Track-Bed™

N Scale

Frequently Asked Questions

HO Scale

Frequently Asked Questions

O Scale

Frequently Asked Questions

Track-Bed^™